Air Conditioning Installations

TRANE HEAT PUMP SOUTH PORTLAND, MESA AZ

This customer reached out to us seeking a new HVAC system for their home. We were happy to install a new Trane 16 Seer 2 Stage Heat Pump with a Variable Speed Air Handler. We also installed new trapeze for the air handler, a new full size emergency drain pan, a new return plenum box, and a new collar for the return duct. Since the customer did not have a secondary drain line, we installed a new condensate drain line safety switch into the primary drain line and the emergency drain pan. We made sure to seal all connections and penetrations at the air handler and ran a new wire for the thermostat for the correct amount of wires needed for the second stage. We also ran a new wire for the condenser for the correct amount of wires needed for the second stage as well. We were able to re-use the customer’s current thermostat and we installed a new electrical disconnect with a whip and surge protector for the new condenser outside. Our customer was able to take advantage of an SRP Rebate for their new Multi Stage System. As with every job, we provided an Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP - SOUTH LABELLE, MESA AZ

This customer contacted us through our website about a new unit consult and a home evaluation. We were able to give the homeowner three options on a new unit so they could choose the one that worked best for their family. We installed a new 3.5 ton Trane split attic heat pump. The air handler was installed with a new full length pan, supply and return boxes, collars with dampers, a safety switch, and all duct work was sealed at the unit. The condenser was installed with a new disconnect, whip, and surge protector. We did a complete start up and QCA and the new system passed with flying colors. As with every job, we provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP E 9TH DRIVE, MESA AZ

This customer reached out through our website about getting a new heat pump for their home. We were happy to install a new 3.5 ton Trane heat pump. We installed a new stand, added a new surge protector, and replaced the high and low volt whip. We also installed a new p trap and tied it into the existing drain line. We installed a new honeywell T6 thermostat for the customer and showed them how to operate it. Before we left, we made sure to seal all the connections and completed a start up test and QCA. As with every job, we provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP 539 SOUTH QUINN MESA, AZ

When it was time to replace their furnace, they new exactly who to call. Our Comfort Advisor met with the homeowner, went over their options and provided quotes. The homeowner decided to go ahead with the replacement. We installed a new Trane 14.3 Seer Split Heat Pump w/Standard Air Handler. To help ensure proper operation we installed a full emergency drain pan, and also insulated the supply plenum with dampers to adjust air flow. We re-used the return chase, properly sealed all connections and penetrations to the system, and even cleared both the primary and secondary drain line. We were happy to install a condensate drain line safety switch with a p-trap into the primary drain line. We installed a new condenser pad for the condenser outside, installed a new electrical disconnect with a whip, a new surge protector and we re-installed the outlet connected to the disconnect. Our technicians also installed line-hide for the refrigerant lineset and a new Trane nexia thermostat. We also built a plywood walkway up in the attic so the system can be serviced easily in the future. After performing a QCA start up and checklist, we ensured the heat pump was running within manufacturer specifications. As with every job, we provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP - SOUTH LOOKOUT RIDGE, GOLD CANYON AZ

After calling us for a quote on an HVAC system replacement, the customer chose to go ahead and get a new unit. We were happy to install a new 3 ton Trane heat pump for them with a new filter base, insulated transition, a new p trap with safety switch, a new low volt pigtail, and a new armor flex. We made sure to seal all connections and added a new disconnect with whip and a new condenser pad. After performing a QCA start up and checklist, we ensured the heat pump was running within manufacturer specifications. The system is covered by a 10 year warranty. As with every job, we also provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP - 10th STREET, TEMPE AZ

Our customer called us about problems they were having with their HVAC unit. We installed a new 3 ton Trane package heat pump. The unit was installed with a new elbow and transition, stand, disconnect, whip, surge protector, and all duct work was sealed from the roof to the unit. We also installed a Nexia 824 thermostat. After a complete start up and QCA check, our customer was able to enjoy perfect temperatures in their home. The customer was also able to save $450 with SRP Instant Rebates on their new Multi-Stage System! The system is covered by a 10 year warranty through the manufacturer. As with every job, we also provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP - 10th STREET, TEMPE AZ

Our customer called us about problems they were having with their HVAC unit. We installed a new 3 ton Trane package heat pump. The unit was installed with a new elbow and transition, stand, disconnect, whip, surge protector, and all duct work was sealed from the roof to the unit. We also installed a Nexia 824 thermostat. After a complete start up and QCA check, our customer was able to enjoy perfect temperatures in their home. The customer was also able to save $450 with SRP Instant Rebates on their new Multi-Stage System! The system is covered by a 10 year warranty through the manufacturer. As with every job, we also provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

Daikin Heat Pumps w Broadway Road, Mesa AZ

We’ve been working with this customer for a while and we are always happy to service their many units on their commercial building. This week, it finally became time to replace them! After a lot of preparation, we installed 4 new Daikin 208/230 3phs Pack Heat Pumps on their roof using a crane. To improve airflow efficiency throughout the building, we installed dozens of feet of ductwork along the ceiling of the interior of the building and removed the Evap Cooler and Caps. We also ran drains and low volts after finishing installing ductwork and hanging cables. This install included a Curb Adapter, a Downshot Supply 4 way air delivery system, with a Downshot Return Air Duct System. These systems are covered by manufacturer warranties and as with every job, we also provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

Trane Heat Pump - Hawes Road, Mesa AZ

This customer was a referral from another one of our fantastic customers! We are always happy to hear that our customers are so satisfied with our work, they spread the word around the community. For this new referral, we installed a 3 ton Trane package heat pump. The unit was installed with a new disconnect and new duct work was connected and sealed. We also cleaned all the duct work and installed an add-a-wire as well as a remi halo. After performing a QCA start up and checklist, we ensured the heat pump was running within manufacturer specifications. As with every job, we provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

TRANE HEAT PUMP - WEST POSADA AVENUE MESA, AZ

This customer contacted us expressing their need for an expert with extensive knowledge about airflow. They not only wanted a new heat pump, but also wanted to ensure that all the vents around the house were receiving the same amount of airflow with the new renovations. We were able to do a thorough inspection of the customer’s ductwork system to meet their needs and explain how the venting system would work with the changes. We were happy to install a 2 stage 3 ton package heat pump by Trane. We rotated the unit 90 degrees and added a transition and elbow to better optimize the system. We re-ran both high volts and low volts to fit the new unit placement and installed a new drain, stand, disconnect, whip and surge protector. Last, but not least, we installed a new Nexia thermostat. All supplies now have dampers for airflow adjustment. After performing a QCA start up and checklist, we ensured the heat pump was running within manufacturer specifications. These parts and compressor have a 10 year warranty. As with every job, we also provided an “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance.

Trane Heat Pump - EAST NEVILLE AVENUE MESA, AZ

Our customer called us to come look at two AC units that were no longer cooling his home. Since the units were old and had kicked the bucket, our customer also wanted an estimate to replace them. We were happy to install two new Trane heat pumps to keep his house nice and cool. Both systems received a new full-size emergency drain pan, a condensate drain line safety switch into the primary drain line, a new supply and return plenum boxes with collars and dampers, new connections, and penetrations sealed. Our technician strapped up all ductwork to allow a more even airflow path. We completed start-ups for both systems and charged both systems to manufacturers' specifications. Both systems have a 10-year parts warranty, a 10-year compressor warranty, and a 2-year labor warranty. And of course, Johns Heating, Cooling, and Plumbing will cover the systems with their Money-Back Guarantee!

Trane Heat Pump - 10th Drive Mesa, AZ

This customer called us to say that their A/C unit stopped blowing cold today, and that the system had shut off! We ran over to investigate, climbed onto the roof, and found out that their 30-year-old Mini-Split, Central AC Package Unit had finally kicked the bucket. RIP. We were glad to help out the customer by installing a new Goodman Heat Pump with a new stand for the unit. We installed a new electrical disconnect and ran a new electrical whip from the attic, through the roof, and to the new disconnect. We installed a surge protector into the disconnect as well, and made sure to seal all penetrations into the roof and connections to the unit. We installed a TY into the return ductwork, cut and installed a new return with a 14” flex, and installed a new Honeywell T6 thermostat. With a new Supply/Return Air Run, we lowered resistance in the ductwork to the unit, lowered noise levels, and increased airflow. This new system cools/heats faster, and provides even temperatures for our customer. Now the mourning period is over, and the celebration can begin! Like all of the systems we install, this system meets manufacturer installation requirements and has a manufacturer warranty - This system has a 10 year parts and 10 year compressor warranty. We also provide our “Installed Right” Guarantee and our Money-Back Guarantee for the first year of its performance.

Trane Heat Pump - 131st Street, Chandler, AZ

Our customer called us out because their 12-year old AC system was not keeping up during the late afternoon the other day. Upon inspection, we found the air conditioner was operating but had some issues. We found that the indoor blower motor had a slight bearing play causing the blower wheel to wobble when spinning. The contactor was burnt and pitted, as well as the indoor coil had a buildup of debris and dust. The dual capacitor for the compressor was below tolerance. Due to the system’s age, current condition, the cost of repairs, the lack of warranty, and the overall unreliability, the customer agreed to move forward with a 2-stage option heat pump. To ensure efficiency we gave the unit a new stand and an insulated elbow, a new disconnect and a new Honeywell programmable thermostat. To protect efficient air flow (to reduce wear and tear on the system) we sealed all the connections and performed a complete start up and QCA test. Like all of the systems we install, this system meets manufacturer installation requirements and has a manufacturer warranty - This system has a 10 year parts and 12 year compressor warranty. We also provide our “Installed Right” Guarantee and our Money-Back Guarantee for the first year of its performance.

Trane Heat Pump - E Main Street, Mesa, AZ

Customer called us out because the temperature on the thermostat was rising. Upon arrival, we found cool air being pushed from vents although the temperature in the home was higher than the set point on the thermostat. Upon inspection of the heat pump system, we found that the dual capacitor was below tolerance on the compressor side. Although we also found other issues such as condenser fan motor having oil loss and bearing play. The insulation had also fallen off the interior of the blower panel, allowing insulation to be sucked up against blower housing! Due to the systems age, current condition, cost of repairs, lack of warranty, and overall reliability, we recommended a new system and a one-year Johns HVAC maintenance agreement. We were happy to install a 2 ton Trane heat pump. We put on new 12” collars, a new disconnect with a whip, and a new p trap. We made sure to properly seal all connections and did a complete startup and quality check. This system has a 10 years parts and 10 years compressor warranty.

Trane Heat Pump - E McKellips Rd, Mesa, AZ

Our customer had three different bids to install a new unit, and chose to trust John’s with the heat pump installation! We were happy to install a new vertical Trane Heat Pump. To ensure maximum efficiency we modified the ductwork to fit the new unit, modified the platform to allow the most airflow for the new air handler, secured the filter frame to the platform, and the air handler to the filter frame. Plus we sealed all connections and penetrations and we added an electrical disconnect for the air handler to allow easy high voltage shut-off and to maintain the builders’ code. We added a condensate drain line safety switch into the primary drain line, ran new thermostat wire, and installed a new Honeywell programmable thermostat. We installed a new condenser pad for the new condenser, removed the old concrete pad, and installed a new electrical disconnect and whip for the condenser. We also ensured the drain line was properly leveled and draining. Finally, we replaced a mass of cork tape covering the line set coming out of the wall with proper metal plating. This system is charged to manufacturer's specifications and has a 10 year parts warranty and a 10 year compressor warranty.

Trane Heat Pump - W San Angelo, Gilbert, AZ

Our customer called Johns because they were not getting cool air from their 11-year-old unit. We went over and found the system’s filter and evaporator were plugged-up, the low voltage wires frayed, and the condensation drain broken. We also found that water had flooded the inside so badly over time, it caused the bottom of the unit to be rusting out! The unit was in such bad shape the evaporator was also rusting and at risk of leaking Freon. The customer decided to have us replace their old unit with a new 3 ton 2 stage Trane Heat Pump. We added a new stand, a new P trap and PVC, and a new disconnect and whip with a surge protector. We installed a wire kit for 2 stage cooling and a cut in a 12” return before sealing all connections thoroughly. This system is covered by a 10 year warranty and backed by John’s exclusive installation guarantees.

Trane Package System Installation - N Stapley Dr, Mesa, AZ

We were called out to address a cooling issue. The customer’s system wasn’t keeping the room cool enough. We performed a thorough diagnosis and found many problems with their system, including cracked and exposed wiring, a burnt contactor, oil leaking from both indoor and outdoor motors and also the indoor coil. Due to the age of the system, lack of warranty/reliability, and the costs of repairs, the customer decided to replace the system. We were happy to install a new Trane 14 Seer Single Stage Package Heat Pump on the roof. We switched out the fuses to match the new unit, extended low volt wires, and ran a high volt whip to the new unit. We also installed a new thermostat and ran a QCA start-up and checklist. Like all of the systems we install, this system meets manufacturer installation requirements and has a manufacturer “Installed Right” Guarantee, along with our Money-Back Guarantee for the first year of its performance. All parts have a 1 year warranty, except for the compressor which has a 5 year warranty.

Double Trane AC Install - E Washington Ave, Gilbert, AZ

We installed two Trane air conditioning systems in this Gilbert, AZ home. Included are a new full-size pan, new insulated plenums with dampers, new gas whip and shut-off valves, and new flu vents. Sealed all connections. New disconnects with whips and pads. Complete start-up and QCA were achieved, ensuring both systems are ready for their new home with our happy customer.

Trane AC Install - E Boot Track Trail, Gilbert, AZ

This customer’s system contains two zones and one zone would cool down properly, but the second area will not cool down. The system is freezing up on the outside and is low on refrigerant. We suggested getting information on upgrading the system. The customer would like to move forward with upgrading their system We installed a Trane air conditioning system. New full-size pan, with new insulated plenums with dampers, and a new Trane comfort control thermostat. Complete start-up was achieved. Customer is very pleased with their decision.

Trane AC Install - Olla Ave, Mesa AZ

John's installed a Trane air conditioning system and furnace. New full-size pan. We cleared drains and installed a new safety switch, new insulated plenums with dampers, new gas shut-off valve and whip, new flu vent, and a new 824 thermostat were also installed. Sealed all connections. New disconnect with whip and surge protector, new condenser pad and hard start kit. Cut in new 12” return. Complete start-up and QCA achieved. Happy to help these customers stay cool this summer! This install includes 10 years parts, 10 years compressor, 20 years heat exchanger, and 2 years labor warranties as well as John's installation and replacement guarantees.

Double Trane AC Install - E. Betsy Ln., Gilbert, AZ

We were called out to this customer’s home. The outside AC unit was not turning on. Since the current system was old, it was decided that replacement was necessary. We installed 2, 3-ton Trane furnaces and air conditioning systems. New full-size pan, new gas shut-off valve and whip, new flu vents, and a new drain line with safety switch were also installed. New insulated plenums with dampers were installed and we sealed all connections. New disconnect with whip. Complete start-up and QCA were achieved. These systems are covered by 10 years parts, 10 years compressor, 20 years heat exchanger, and 2 years labor guarantees.

Double Trane Heat Pump Install - E. Mineral Road, Gilbert, AZ.

This customer’s heat pump failed and needed to be replaced. We Installed two heat pumps, 2 4-ton 2-stage Tranes. A new full-size pan and new insulated plenums with dampers were installed as well as new p traps with safety switch and A new 824 thermostat. We then sealed all connections. Complete start-up and QCA were achieved. Both systems are covered by a 10-year parts, 10-year compressor, and 2-year labor guarantee.

Trane Split System Installation - E Wilshire Dr, Scottsdale

Customer phoned and requested service for his A/C unit which was not reaching cool temperatures. He requested an estimate for a new system, as this was an old unit. Ultimately, they decided on a Trane 16 Seer2 horizontal gas split system furnace to make their living space more comfortable. This system is covered by a 10 years parts, 10 years compressor, 20 years heat exchanger, 2 years labor and, of course, John’s service & repair guarantees.

Trane Split System Installation - E Harrison St., Gilbert

A John’s customer contacted us because no cool air was coming from their air conditioner. This customer has two older HVAC systems in their home. After discussion, the customer decided to entertain estimates for new system and opted to replace the old systems with newer and more energy efficient Trane 3 & 4 ton, 2 stage, Seer 2 split units with outdoor condensers and coils. All of these are covered with John’s impeccable installation and replacement guarantees. Another customer saved from the Arizona heat!

Trane Split System Installation - N Judd Pl, Chandler

Customer was looking to replace HVAC units right away and called John’s for an estimate. The customer decided that a double attic Trane furnace system with outdoor condensers was their best option! Of course, installation was covered and our customer by John’s guarantees: our Money Back, Installed Right, Accurate Quote, and Home Protection Guarantee. We love making our customers comfortable when they need it the most.

Trane Split System Installation - E. Milagro Ave, Mesa

Customer called because his AC unit was being noisy and wondered if it would be better to repair or replace his older unit. The morning of the service call, his AC quit working! It was determined that a Trane split system, two stage compressor with a WIFI thermostat would be the best option. Furnace was installed in attic while A/C compressor was installed outside the home. Of course, installation was covered and our customer by John’s guarantees: our Money Back, Installed Right, Accurate Quote, and Home Protection Guarantee. Another happy and cool customer ready for the Arizona heat!

Trane Furnace/AC Replacement - Phelps Street, Gilbert AZ

We installed 2 new Trane single stage split systems with A/C coils and furnaces located in the attic. Condensers were installed outside of the residence. The furnaces were installed with new supply and return boxes, collars with dampers, safety switches, full length pans and all duct work at the unit was sealed. The condenser was installed with a new disconnect, whip, and surge protector. We did a complete start up and QCA. 10-year parts, 10-year compressor, 20-year heat exchanger, 2-year labor warranties.

Trane Furnace/AC Replacement - E. Marino Drive, Scottsdale, AZ.

We installed 2 new split systems with 1 Furnace located in the attic and 1 in the garage at this home. The attic furnace was installed with a new full length pan, supply, and return, collars with dampers, a safety switch, new gas pipe from the unit to the shut-off, and all duct connections were sealed. The garage unit was installed with a filter base new gas whip and shut off, safety switch, blew out drain line with nitrogen and sealed duct connections at the unit. Both condensers were installed with new disconnects and whips. We did a complete start up and QCA. Both systems include a 10-year parts, 10-year compressor, 20-year heat exchanger, and 2-year labor warranties.

Trane A/C Replacement – Juanita Ave, Mesa Az.

A John’s customer inquired about replacement for two HVAC systems in their residence. We installed a 5 and 3 ton Trane split attic systems. Both systems were installed with new supply and return boxes. Both condensers were moved around the corner to the side of the house, laid down new condenser pads, and extended electrical high and low volts. A complete start up and QCA were performed. Super satisfied that this customer will be enjoying quality heating and cooling for years to come! These systems are each covered by a 10-year parts, 10-year compressor, 20-year heat exchanger, and 2-year labor warranties.

Trane A/C Replacement – 1st Street Mesa Az.

A customer called and wanted an estimate to replace the two 20-year-old HVAC systems that were in his home. We installed a 5-ton furnace in a closet inside the home and a 3-ton furnace in the garage. Installed surge protectors. We then installed new Nexia communicating thermostats. Charged the systems to the manufacturer's specs and both systems were running properly. This customer will enjoy fantastic heating and cooling for years to come. Both units have warranties of: 10-year parts warranty, 12-year Compressor warranty, 20-year heat exchanger warranty, and 2-year labor warranty.

AC Installation East Placer Drive Gold Canyon AZ

During a routine maintenance visit, our technician found that the air conditioning had developed a leak and was low on refrigerant. When performing additional diagnostics, the capacitor was not operating correctly, and the contactor was pitted and burned. Our technician presented his findings and went over the options to repair or replace the system. Due to the age, current condition, cost of repairs, lack of warranty, and overall reliability, the customer decided to replace the system. John’s Heating, Cooling, and Plumbing installed a Trane 14.3 Seer Split Heat Pump w/Standard Air Handler located in the attic above the garage. This installation is Pearl Certified and covered by a manufacturer's ten-year parts and compressor warranty. In addition, we cover all installations with our Installed Right Guarantee and Money Back Guarantee.

AC Replacement Mountaingate Dr. Gold Canyon AZ

We saved our customer in Gold Canyon a ton of money by helping him combine the SRP utility rebates and our current promotions. We installed a 4-ton Trane split attic heat pump with a Nexia 824 thermostat. In addition to the ten-year parts, ten-year compressor, and two-year labor warranties through the manufacturer, we also cover all installation with our Installed Right Guarantee and our Money Back Guarantee. In addition, Pearl Certification™ (a comprehensive report) highlights the high-performing assets that this home healthy, comfortable, and energy efficient. Pearl Certification can increase a home's value by an average of 5% when it's time to sell or refinance.

Trane Heat Pump Install – Leisure World in Mesa

A Peak Performance Club member called because their gas furnace was not working correctly. It was the first time they turned on their heating system for the season, and it made a loud noise and would only blow cold air, so they called John’s Heating and Cooling for a furnace repair. After completing a full diagnostic, the technicians determined that the system was low on refrigerant due to the indoor coil leaking refrigerant, which also damaged the indoor coil. Due to the cost of the repairs and the overall reliability of the system, a replacement was recommended. Johns Heating and Cooling replaced the system with a new 3.0 ton package Trane 14 Seer Single Stage Package Heat Pump system on the roof. For improved comfort, safety, and peace of mind, a surge protector and programmable thermostat were also installed. The technicians did a complete QCA start up and checklist and the new system is backed by a 10 year parts, 10 year Compressor, and 2 year labor warranty on top of all of John’s Installation & Replacement Guarantees.

Trane Heat Pump Install – Leisure World in Mesa

John’s technicians were called out for routine system maintenance and performed a 21-point deluxe inspection on a 1998 Goodman split heat pump in Mesa. During this maintenance visit, they found that the system struggled to run at peak performance due to its age, as both the outdoor fan motor and indoor fan motor were showing major indications of bearing play and oil leakage. At this time, it was recommended to the homeowner to consider replacing the air conditioner instead of investing more money into an old system that was out of warranty, and that they could save money on replacing before 2023 when price and efficiency ratings would be increasing. They decided to think about it, and ultimately scheduled a free consultation later that month. The customer did decide to take advantage of a great promotion that was running, so John’s Heating and Cooling installed a 3.5-ton Trane Heat Pump and a Honeywell Programmable Thermostat. The new system is backed by 10-year parts, 10-year Compressor, and 2-year labor warranty on top of all of John’s Installation & Replacement Guarantees.

Payne Heat Pump Install – East Main Street in Mesa

During a routine Peak Performance Club maintenance visit for a customer who had 2 units of differing age, the technicians noted that the older system had a bad outdoor fan motor, a very burnt and pitted contactor, high start amps, and dirty, indoor coil. Due to the cost of repairs, the age of the system, and the overall reliability, they recommend updating the older system to better match the efficiency of the newer system, which would both provide more optimal comfort and reduce utility costs. The technicians at Johns replaced the older unit and installed a 2.5 ton Payne package heat pump. Included were a new 16” flex for the return and supply, a new disconnect with whip and surge protector, and a new p trap and drain line.

Trane Heat Pump Install – East Desert Trail in Mesa

The technicians at John’s were scheduled to perform a 21-point maintenance inspection on a package unit in Mesa. During this time, the techs chemically washed the outdoor coil and discovered the fan motor leaking oil, the contactor burnt and high start amps. Due to the age of the system and the cost of repairs, it was recommended to consider a heat pump replacement, so they set up a free new system consultation to learn more about their replacement options. John’s Heating and Cooling installed a new 2-stage 3-ton Trane package system on the roof. The new system is backed by a 10-year parts, 10-year Compressor and 2-year labor warranty on top of all of John’s Installation & Replacement Guarantees.